3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit

3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit
3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit
3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit
3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit
3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit

3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit
Easy to custom clerance, no damage , better service, please don’t hesitate! 3 pcs stepper motor driver DM542A, peak 4.2A, 128 micsteps, replacing M542. 1 pc Power supply 350Watts (36VDC/9.7A). 1 pc Breakout board & 1 pc Parallel cable. Motor Length L(mm). Holding Torque (oz. In). DM542A is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, whats more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. High performance, low price. Average current control, 2-phase sinusoidal output current drive. Supply voltage from 18VDC to 50VDC. Overvoltage, under voltage, overcorrect, phase short circuit protection. 15 channels subdivision and automatic idle-current reduction. 8 channels output phase current setting. Offline command input terminal. Motor torque is relased with speed, but not related with step/revolution. High hording torque under high speed. Pins assignments and description. Pulse signal, PUL+ is the positive end of pulses input pin. PUL- is the negative end of pulse input pin. DIR signal: DIR+ is the positive end of direction input pin. DIR- is the negative end of direction input pin. Enable signal: ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver. ENBL- is the negative end of direction input pin. Usually left unconnected (enabled). 2 Pins wiring diagram. PCs control signals can be active in high and low electrical level. When the high electrical level. Is active, all control negative signals will be connected together to GND. Level is active, all control positive signals will be connected together to public port. Two examples(Open collector &PNP), please check them. Input port circuit (Yang connection). PC open connector output. 2 Input port circuit (Yin connection). Note: When VCC=5V, R=0. When VCC=12V, R=1K, 1/8W. When VCC=24V, R=2K, 1/8W. R must connect in the control signal part. Function choice (Using DIP pins to achieve this function). 1 Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table. 2 Standstill current setting. SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the. Selected dynamic current and ON meaning that standstill is set to be the same as the selected. 3 Output current setting. The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Closest to your motors required current. Semi-flow function is that there is not step pulse after 500 ms, the driver output current. Automatically reduced to 70% of rated output current, which is used to prevent motor heat. Pins of motor & power. Motor and power pins. The power of this power supply is 350Watts, and the output voltage/current is 36VDC/9.7A. Description: Built in DB25 male connector. DB25 Output Pin:P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. DB25 Input Pin: P10, P11, P12, P13, P15. DB25 GND Pin: P18-P25. Power supply: +5V DC. Built in C-class Optical-coupler. High quality with Surface-mount Tech. We can manufacture products according to customers requirement. Our Stepper Motors are used on small to mid-sized CNC mills & milling machines, CNC lathes, Pick-n-place machines, Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. These motors have been used in precision telescope positioning systems and robots. The item “3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit” is in sale since Thursday, September 4, 2014. This item is in the category “Business & Industrial\Automation, Motors & Drives\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives”. The seller is “longs_motor” and is located in , . This item can be shipped worldwide.
  • holding torque: 425OZ-IN
  • Model: 23HS9430
  • Modified Item: No
  • Country/Region of Manufacture: China
  • Custom Bundle: No
  • MPN: Does Not Apply
  • Brand: longs motor
  • Non-Domestic Product: No
  • current: 3.0A

3axis Nema23 stepper motor 425oz-in 3.0A CNC ROUTER controller kit