12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set

12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set

12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set
CNC Spindle Motor & Tool Parts. Stepper Motor & Driver. Servo Motor & Driver. HMI & PLC Panel. CNC Router & Tools. 12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set. 3 x MA860H Sumtor step motor drive 2ph 24110VDC AC18-80V 27.8A. 3 x 86BYG 2ph Hybrid stepper motor 86HS15060A4. L 150mm 4-lead 6A 12NM 1.8 degree. Switching Power Supply 400W 60V 6.7A for CNC S-400-60. 1 x 5 Axis CNC Breakout Board Interface For Stepper Motor Driver. 1 x DB25 Parallel Cable & USB Power Cable. Shaft Type: double-sided milling flat 1mm. Certification: CCC, CE, ISO. Step angle: 1.8degree. 7.8(5.6RMS). Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode(pulse/pulse) , this input represents clockwise (CW) pulse. Active at high level or low level (set by inside jumper J1 & J2). For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when+12V or +24V used. The same as DIR and ENA signals. DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1 & J2), this signal is counter-clock (CCW) puls. For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that motion direction is also related tomotor-driver wiring match. Exchanging the connection of? Two wires for a coilto the driver will reverse motion direction. Enable signal: This signal is used for enabling/disabling the driver. High levelNPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling. For enabling the driver and low level fordisabling the driver. Power supply, 1880 VDC or 24110VDC, Including voltage fluctuation and EMF voltage. Input voltage: AC110-230V (supports 110V has a pull switch). Output voltage: DC60V 6.7A. Size: 215 115 50MM. 5 axis CNC Breakout Board. Maximum support 5-axis stepper motor driver controllers. Compatible with MACH3, Linux CNC (EMC2) etc. USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V, and with anti-reverse function. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc. Output 0-10V analog voltage for inverter to control the spindle speed. USB port from PC or 12-24V power supply(optional). Pulse and Direction Signal Control. 2 Phase Microstep Driver. 90 70 20mm (LWH). Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you. Due to time zones, our reply to your questions may not be immediately. But within above working time, we w. If it’s non-workdays, please kindly be patient and wait till Monday. The item “12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set” is in sale since Tuesday, June 2, 2015. This item is in the category “Business & Industrial\Automation, Motors & Drives\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives”. The seller is “vipwindows_168″ and is located in Shenzhen. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Australia.
  • Application: CNC Router Lathe
  • Brand: Sumtor
  • Country/Region of Manufacture: China
  • Holding torque: 12NM 1700oz.in
  • Model: 3-MA860H-86HS15060A4
  • MPN: Does not apply
  • Power supply: 400W 60V 6.7A
  • Rated Current: 6A
  • Stepper motor: Nema 34
  • Stepper motor drive: 2ph 24~110VDC AC18-80V 2~7.8A
  • UPC: Does not apply

12Nm Stepper Motor Kit XYZ 3Axis Nema34 L150mm CNC Router Motion Control Set