Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit

Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit

Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit
CNC Spindle Motor & Tool Parts. Stepper Motor & Driver. Servo Motor & Driver. HMI & PLC Panel. CNC Router & Tools. Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit. 3 x MA860H Sumtor step motor drive 2ph 24110VDC AC18-80V 27.8A. 3 x 86BYG 2ph Hybrid stepper motor 86HS11460A4 L 114mm 4-lead 6A 8.2NM 1.8 degree. Switching Power Supply 400W 60V 6.7A for CNC S-400-60. 1 x 5 Axis CNC Breakout Board Interface For Stepper Motor Driver (free offer). 1 x DB25 Parallel Cable & USB Power Cable (please check pictures for details). Shaft Type: double-sided milling flat 1mm. Holding torque: 8.2nm. Certification: CCC, CE, ISO. Step angle: 1.8degree. 7.8(5.6RMS). Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode(pulse/pulse) , this input represents clockwise (CW) pulse. Active at high level or low level (set by inside jumper J1 & J2). For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when+12V or +24V used. The same as DIR and ENA signals. DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1 & J2), this signal is counter-clock (CCW) puls. For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that motion direction is also related tomotor-driver wiring match. Exchanging the connection of? Two wires for a coilto the driver will reverse motion direction. Enable signal: This signal is used for enabling/disabling the driver. High levelNPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling. For enabling the driver and low level fordisabling the driver. Power supply, 1880 VDC or 24110VDC, Including voltage fluctuation and EMF voltage. Input voltage: AC110-230V (supports 110V has a pull switch). Output voltage: DC60V 6.7A. Size: 215 115 50MM. 5 axis CNC Breakout Board. Maximum support 5-axis stepper motor driver controllers. Compatible with MACH3, Linux CNC (EMC2) etc. USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V, and with anti-reverse function. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc. Output 0-10V analog voltage for inverter to control the spindle speed. USB port from PC or 12-24V power supply(optional). Pulse and Direction Signal Control. 2 Phase Microstep Driver. 90 70 20mm (LWH). Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you. Due to time zones, our reply to your questions may not be immediately. But within above working time, we w. If it’s non-workdays, please kindly be patient and wait till Monday. The item “Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit” is in sale since Tuesday, June 2, 2015. This item is in the category “Business & Industrial\Automation, Motors & Drives\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives”. The seller is “vipwindows_168″ and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.
  • Brand: Sumtor
  • Model: 3-MA860H-86HS11460A4
  • Country/Region of Manufacture: China
  • Stepper motor drive: 2ph 24~110VDC AC18-80V 2~7.8A
  • Stepper motor: Nema 34
  • Holding torque: 8.2Nm 1161oz.in
  • Rated Current: 6A
  • Power supply: 400W 60V 6.7A
  • Application: CNC Router Lathe
  • MPN: Does not apply
  • UPC: Does not apply

Motion Control 3Axis Nema34 Stepper Motor L114mm XYZ Axis CNC Router Printer Kit