US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit

US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit

US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit
Great News from Wantaimotor! Please don’t hesitate! 2 PCS Nema 34 Stepper Motor with 1600oz-in holding torque for dual shaft. 2 PCS DQ860MA with 7.8A peak current , 24-80VDC , 256 Microstep. 2 PCS Power Supply for 350W, 60VDC. 1 PC Breakout Board. 1 PC DB25 Cable. Step Angle: 1.8 degree. Resistance: 1.9 Ohm/phase. Holding torque: 11.2N. Number of wire leads: 4. Note: Nema 34 Stepper Motor with 1600oz-in holding torque on dual shaft, front shaft length is 37mm with 25mm flats length, the rear shaft length is 34mm with 25mm flats length, the diameter for motor shaft is 14mm. 2, Stepper Motor Driver DQ860MA. Introduction, Features and Applications. The DQ860MA is an economical microstepping driver based on patented technology of Wantai Motor. It is suitable for driving 2-phase 4-phase hybrid stepping motors. By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as L/R drivers. Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Low cost and good high-speed torque. Supply voltage up to +80VD. Suitable for-2-phase and 4-phase motors. Output current up to 7.8A, 5.6A rated current. Dip switch current setting 8different values. Optically isolated input signals. Pulse frequency up to 200KHz. Small size (1079748), Weight:0.6KG. 3, Power Supply -350W , 60VDC, 5.9A. 500Hz, 2G 10min, /11cycle, 60min, each axes. I/P-O/P:3KVACI/P-FG:1.5KVACI/P-FG:0.5KVAC. I/P-O/P, I/P-FG, I/P-FG:500VDC/100M. 4, Breakout Board DB25. Set pins according to software as follows. Output pin: P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. P2 X axis Pulse, P3 X axis Direction. P4 Y axis Pulse, P5 – Y axis Direction. P6 Z axis Pulse, P7 Z axis Direction. P8 – A axis Pulse, P9 – A axis Direction. P14 – B axis Pulse, P1- B axis Direction. P16 – C axis Pulse, P17- C axis Direction. Input pin: P10 , P11, P12, P13, P15. Set them for Emergency Stop and X Y Z Limit switch. More order quantities, more discount!! Our products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica Machine, Make-up Equipment, Household Appliance, Milling Machine, Engraver Machine, CNC Routers and so on, automatic equipment of various trades. The item “US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit” is in sale since Thursday, March 9, 2017. This item is in the category “Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\Stepper Motors”. The seller is “wantmotor2013″ and is located in CA. This item can be shipped worldwide.
  • Driver/Controller Bundle: Motor with Driver & Controller Board
  • Model: 85BYGH450C-012B
  • Country/Region of Manufacture: China
  • Current Type: DC
  • Wiring Configuration: 4-Wire Bipolar
  • MPN: Does not apply
  • Full Step Angle: 1.8° (200 Steps)
  • Holding Torque: 1600OZ-IN
  • Brand: WANTAI

US free! Wantai 2Axis Nema34 Stepper Motor dual Shaft 1600oz-in CNC Router Kit