CNC Kit 4 Axis Breakout Board & Nema23 Stepper Motor For DIY Router/Mill/Plasma. 4 Axis Kit for CNC DIY. M Stepper Motors + 124V 10A Switching Power Supply. The 5 axis breakout board in this kit is specially designed for CNC single axis stepper driver controller. Maximum 5 pcs can be connected. In the market, such as ENGMATE series, M542, M542H, MA560, MA860H, 2M542, 2M982, DM542(A), DM860(A) etc.. It can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. The stepper driver board controller in kit is a high performance microstepping driver adopting of 32-bit DSP, pure sine wave subdivision technology. With this technology and the self-adjustment technology (self-adjust current control parameters) for different motors, the drive motors can run with less noise, lower heating, smoother movement and have better performances at higher speed than most of the drivers in the market. In short, you will get more benefits from the Kit on CNC work, especially extra-low motor noise offers excellent quietness. 10+ Years Rich Experience. We have been fulfilling CNC Motion Control needs for over 10 years to support any project you may have. Stepper motors and drivers from ENGMATE. Are with high quality for stable and durable usage. Upgraded circuit, work more peacefully and steady than the previous version. Stepper motor driver controllers. To get power: 5V DC power supply or USB port to get power from PC directly. Signal processing, smooth signal transmission, powerful anti-jamming. Interface to define the Limit, Emergence-Stop, Midpoint-Alignment, Cutter-Alignment, etc. Relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. Visually display the working condition of the stepper driver controller. Digital Hybrid Microstepping Driver. Extra-low motor noise offers excellent quietness. Supply voltage from. Output current programmable. With 8 stalls output current setting. 1.0A-4.2A(Peak). Adoption of 32-bit DSP, pure sine wave subdivision technology. Low-vibration and low temperature rising. Microstep resolutions programmable. With 15 stalls microstep subdivision setting. Automatic half-current reduction as long as switching off SW4 when motors stop. Internal optical isolation, pulse input frequency up to. Short-voltage, over-voltage, over-current and short-circuit protection, protect the motors, driver from being damaged. Suitable for 2-phase and 4-phase Hybrid stepper motors. High torque, more smooth movement. High efficiency, energy-saving, low noise and low vibration. High start torque, low start current and reliable performance. Simple 4 wires ensure easier wiring, installation and maintenance. High efficiency, high reliability, low cost. PWM control and regulation, insure the steady and precise output voltage. Over-temperature protection: built-in a powerful fan for cooling. Built-in EMI filter. 100% full load burn-in test. Over current, over voltage, short circuit. Low output ripple and yawp. Suitable for a variety of small sized automation equipment and instruments. For any small-and-medium automatic equipment with CNC controller, such as engraving machine, plasma cutting machine, milling machine, foam cutting machine, lathes, laser cutting machine etc.. For other industrial application, such as 3D printer, medical instruments, stage light equipment, robot, music fountain etc.. Recommended ENGMATE Stepper Motors. Electrical Properties of 5Axis Breakout Board(ambient temperature Tj = 25°C). 5V DC via power adapter or directly get power from PC via USB port. Pulse + Direction + Enable Signal Control. 2 Phase, 3 Phase, 4 Phase Microstep Driver EMA2-050D42/EMA2-070D56/EMA2-080D72/EMA2-220A80 etc. Natural Cooling or Fan Forced cooling. Avoid dust, oil fog, corrosive gas. Nema 17, Nema 23. 250W 24V 10A Switching Power Supply 110/220V Switchable Temperature Control. 110VAC/220VAC±20%(selected by switch). Output Voltage Adjustment Range. (Subject to Stock Availability). (May depart from other stock location). Need the item urgently. Require that the item should be delivered within a certain time. It is not guaranteed that parcel should arrive within the time stated above. However, 95%+ parcels will be delivered within the reference time. We will help you to track them. All sales are final. If you receive a not-as-described e. We will arrange a replacement as soon as the case is confirmed. All qualified return/replacement must be guided by us. We may not accept your return without communication in advance. By placing an order, you acknowledge that you have accepted the terms and conditions of sale. The item “CNC Kit 4 Axis Breakout Board & Nema23 Stepper Motor For DIY Router/Mill/Plasma” is in sale since Thursday, November 7, 2019. This item is in the category “Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives”. The seller is “savebase” and is located in Los Angeles. This item can be shipped worldwide.
- Brand: Generic
- MPN: 10103170111100736