Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large

Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large
Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large
Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large
Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large
Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large
Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large

Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large
You may also like. Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router – Large. The MACH3 Controller Bundle contains all the hardware for powering and controlling your WorkBee, Ox CNC or other CNC machine. The cables on this “Large” Bundle are designed for machines of the following sizes. For smaller machines see our MACH3 Controller Bundle – Small. 1 x Mach3 5 Axis STB5100 USB motion card. 1 x TB6600-T4 4 Axis stepper motor driver board. 4 x signal cables. 1 x USB cable(With two magnetic shield). 1 x CD (Instructions and softwares of trial version). 1 x MEAN WELL Power Supply – 24V 350W. 4 x 4 Core Shielded Cable (use for X Axis, Y Axis, Z Axis and A Axis). 3 x 2 Core Shielded Cable (use for X Axis, Y Axis, Z Axis). 1 x DC Power Cable. 1 x Ground Wire. 1 x E-Stop Switch + E-Stop Cable. 3 x Limit Switch Kits. Thank you for attention. TB6600-T4 4 axis driver board, the biggest advantage is that it can connect the parallel interface board and also can connect. The USB interface board. To meet the customer’s needs. Using the Toshiba TB6600HG driver chip, the maximum output of 4.5A. Current, current stepless adjustable, 4 stepper. Motors can be driven at the same time, suitable for NEMA17, NEMA23 stepper motor. Has a 12Vpower supply, can be used for MACH3 interface. Board or CNC controller; have large driver current, smooth running. Quiet small volume, convenient installation, high cost performance, It is suitable. For making CNC machines and other automation equipment. Support for Windows XP, Windows 7 32/64bit, Windows8, Windows10 operating system. Applicable to all versions of mach3 software. Support for CNC controlled 5-Axis, can connect five stepper motor driver or servo driver. The maximum output pulse frequency is 100KHz, and the pulse width can automatically change with the pulse frequency, which can be applicable. To the closed-loop driver of strict requirements on pulse. Five optocoupler isolation input signal interfaces: limit switch, emergency stop switch, auto tool zero sensor, home switch, NPN sensor switch can be connected. Inverter control signal interface (optocoupler isolation): Output 0-10V speed control signal, PWM speed control signal, spindle start control signal. Used for mach3 software to control spindle’s speed, start and stop. Four universal output signal interfaces, the maximum output 500MA current, can drive relays, solenoid valves, used to control mist, pumps, cylinders and other equipments. Support for external connect electronic hand wheel, use HDR15 interface to connect electronic hand wheel, used for manual control of machine tools. Add the enable signal interface, can be used to control the driver enable signal. The power of control card: voltage 12-24VDC, current more than 500MA. TB6600-T4 stepper motor driver board’s features. DC Power input type:+14V40V. Output current:04.5A, current stepless adjustable. 3.12V Power output : Maximum output 2A current, for CNC controller or Mach3 interface board power supply. Automatic half current function: when the motor stops running, the standby current is automatically reduced to half of the working current to reduce the heat of the driver. Mircostep: 1,2,4,8,16. Automatic decay function: the chip adjusts the current decay mode according to the motor parameters and running speed to reduce the noise of the driver. Protect form : Overheated protection, over-current protection. The maximum pulse rate is 200KHZ. Using the PWM chopper – type single – chip bipolar sinusoidal Micro – step current control mode. MEAN WELL Power Supply – 24V 350W. Output Voltage-Channel: 24 V. Output Power: 350.4 W. Input Voltage: 90 VAC to 132 VAC/180 VAC to 264 VAC, 240 VDC to 370 VDC. Output Current-Channel: 14.6 A. Input Frequency: 47 Hz to 63 Hz. 4 Core Shielded Stepper Cables terminated at one end with JST SM 4P (Connector to Stepper Motors): 4 pcs. 2 Core Shielded Signal Cables terminated at one end with JST SM 2P: 3 pcs. 3 x Micro Limit Switch. 3 x Limit Switch Plate. 6 x M3 10mm Cap Head Screw. 3 x M5 8mm Low Profile Screw. 3 x M5 Drop-in Tee Nut. The holes in the switch will need to be opened a little (3mm drill bit) to allow for the M3 screw or alternatively you can use a M3 tap to cut a thread into the plastic. Max Voltage AC 660V. Rated Load: AC: 220VAC/6A, 380VAC/4A, 660VAC/2A DC: 440VDC/0.3A, 220VDC/0.5A, 110VDC/1A. Withstand Voltage: 2500V /60S. Return must include all original package and accesorries, item must in good condition. Please do NOT leave negative or neutral feedback without asking for help. We will try our best to solve your problem to your satisfaction. We are always here with you! The item “Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large” is in sale since Monday, April 15, 2019. This item is in the category “Computers/Tablets & Networking\3D Printers & Supplies\3D Printer Parts”. The seller is “bulkman3d” and is located in GuangDong. This item can be shipped worldwide.
  • Brand: Bulk-Man 3D
  • MPN: Does Not Apply
  • SKU: MPSTB5100-L
  • Motor Type: Stepper Motor
  • Power Supply: DC

Mach3 USB 5 Axis CNC 100KHz Stepper Motion Controller Kit for CNC Router Large